Getting Started with Your Precision Reed Tester - BagpipeLessons.com
Product helpPrecision Reed Tester and Drone AdapterJori Chisholm, BagpipeLessons.com. Updated November 2026

Getting Started with Your Precision Reed Tester and Drone Adapter

Thank you for getting the Precision Reed Tester and Drone Adapter: two tools in one for your Bagpipe Gauge. Play with all three drones going while you watch your pressure, and measure the exact pressure of any chanter or drone reed so you can match them precisely.

Quick start: get a good fit

  1. Add a little of the hemp you already use to the joint, or wrap a thin strip of cardstock around the hemped joint (the colored instruction card is the right material).
  2. Fit the adapter until the seal is snug and airtight. Leave a small tail of hemp hanging out so it’s quick to remove.
  3. Plug the Bagpipe Gauge tube into the side port of the adapter.
  4. Check your reading. If the gauge reads low or zero, you have an air leak, so add a little more hemp or cardstock.

The adapter is made a little loose on purpose. There’s no standard size for drones and chanters, so you make your own airtight seal. It takes about 30 seconds and won’t disturb the hemp already on your joints. You need a Bagpipe Gauge to use it.

At a glance

Two tools in oneA drone adapter and a precision reed tester
Works withEvery Bagpipe Gauge, old and new
FitMade loose on purpose: seal it with hemp, cardstock, rubber or leather
Accurate readingsNeed an airtight seal
Works onAll pipes, including Border pipes and smaller-bore pipes

Using the reed tester

  1. Place the adapter securely over the chanter or drone reed, adding material as needed for a snug, airtight fit.
  2. Plug the Bagpipe Gauge tube into the side port.
  3. Blow steadily through the top of the adapter and watch the gauge.
  4. Note the pressure when the reed first starts to sound, when it locks into full tone, and when it shuts off.
  5. Write the numbers down so you can compare and match your reeds.

Your goal: match all three drone reeds to each other at your chanter reed’s target pressure, using the least air possible while keeping a steady tone. Download the free Reed Matching Roadmap.

Using the drone adapter

  1. Take one drone out of its stock. Any stock works, because the pressure in the bag is the same everywhere. I use the outside or middle tenor.
  2. Add some hemp to the narrow end of the adapter and put it into the drone stock.
  3. Put the drone, with its reed, back into the adapter, and check for a secure, airtight fit.
  4. Plug the Bagpipe Gauge tube into the side port.
  5. Strike in and play normally, with all three drones going, while you watch your pressure and practice steady blowing.

Tips for a good fit

The hemp method

Add a little of the same hemp you already use until the joint is snug and airtight. Leave a small tail hanging out so it’s easy to remove.

The cardstock method

My favorite: wrap a thin strip of cardstock around the hemped joint for a tight fit that comes off easily. The colored instruction card in the box is the right material.

Other materials

A thin strip of rubber or leather around the hemped joint works well too.

Bonus tuning tip

With the adapter in a drone, use your favorite tuner app with the InTune Mic to tune your pipes while you watch your pressure.

For pipe bandsEquip your whole band

Band pricing: 15% off orders of 10 or more. The discount is applied automatically at checkout.

Shop the Reed Tester

Your questions, answered

Do I need the Bagpipe Gauge to use this?

Yes. It’s designed to work only with the Bagpipe Gauge.

Will it work with my older Bagpipe Gauge?

Yes. It works with current and older Bagpipe Gauges.

What if the stopper doesn’t fit the side port?

The port is sized for the Bagpipe Gauge tube stopper. If the stopper is a little small, wrap a few layers of electrical tape around it. If it seems a little large, push it in firmly. If you need a replacement, contact us.

Why is the adapter loose on my chanter and drones?

That’s on purpose. Bagpipe sizes vary, so the adapter is made to fit every set, and you add hemp, dental floss or cardstock to make your own airtight seal.

Will it work with non-standard pipes?

Yes, including mouth-blown Border pipes and smaller-bore pipes. If the adapter fits, you can use it. Contact us if you have special needs.

What if my drone bore is unusually small?

That’s rare, but it happens with some makes. Email us a clear photo and the exact inside diameter of your stock, and we may be able to make or find a custom adapter.

How do I make sure the reading is accurate?

The connection has to be airtight. If the gauge reads low or zero, you probably have an air leak, so add more hemp or a cardstock wrap.

Can I use it with moisture control systems or drone valves?

Yes. They may change the readings slightly, but everything still works. Try taking them out to see how much they affect your readings.

Videos to watch

Need help? Contact us or email [email protected], and we’ll get back to you.

Jori Chisholm, inventor of the Bagpipe Gauge
Inventor of the Bagpipe GaugeJori Chisholm

I created the Bagpipe Gauge and the Precision Reed Tester so pipers could see their pressure and set up their pipes with confidence. I founded BagpipeLessons.com in 1999 and have taught the bagpipes full time ever since. I’m also the inventor of the Tone Protector and the InTune Mic.

More about Jori →